Clear Coating Epoxy Resin

Our Favourites

Clear Coating Epoxy Resin

$22.00$1,084.30
In-Store/Phone Orders (per unit/metre): $23.95-1095.15

Clear Coating Epoxy Resin is a water clear, UV stable, low viscosity resin system for coating, doming and resin art applications.  It is a solvent free epoxy specifically formulated as a clear, ultra-high gloss coating system that will self-level and cure at room temperature. The system has excellent air-release and has been optimised for extended UV stability.

SKU: CCRF Categories: ,
    Clear
    • Description
    • TDS/SDS

    Description

    Clear Coating Epoxy Resin is a water clear, UV stable, low viscosity resin system for coating, doming and resin art applications.  It is a solvent free epoxy specifically formulated as a clear, ultra-high gloss coating system that will self-level and cure at room temperature. The system has excellent air-release and has been optimised for extended UV stability. This resin is not suitable for embedding, casting or coating more than 2mm thick, we recommend our Bio Casting Resin Slow Hardener for these applications.

    Coverage:

    1 litre = 0.6 square metres, approximately subject to the subtrate it is being poured onto.

    Mix Ratio

    90 parts hardener to 100 parts resin by weight
    1 part hardener to 1 part resin by volume

    Note: Care should be taken when dispensing and mixing.  Do not attempt to control the cure time by altering the hardener ratio. Please note that the room temperature will affect cure characteristics. Measure and mix Clear Coating Epoxy Resin with hardener using our range of measuring and mixing equipment.

    • Pot Life – 100g @ 25ºC (in air): 38 minutes
    • Thin Film Tack Free Time @ 25ºC: 7 hours
    • Thin Film Open Time @ 25ºC: 40 – 60 minutes
    • Cured to Solid State @ 25ºC: 24 hours
    • Shore ‘D’ Hardness 24h@ambient +16h@40ºC: 76
    • Ideal for resin art, coating and doming applications
    • Easy clean up with isopropyl alcohol or acetone
    • Can use Pearlex, BJB and PSTF pigments to colour resin

    Application

    The surfaces to be coated should be dry and free from contaminants. Use two clean plastic containers of equal volume to measure the correct proportion of resin and hardener. Pour the contents of both into a larger container and stir the two ingredients thoroughly, for at least 3 minutes –longer in cooler temperatures. Tip the mixed resin and hardener into a second large container and thoroughly mix again for a further 1-2 minutes. Take care to stir the material slowly so air entrapment is kept to a minimum.

    Clear Coating Epoxy Resin may be directly poured or brushed onto a surface and will self level to produce a very high gloss. For best results apply at temperatures between 15ºC and 35ºC, and at below 85 percent humidity.

    Air bubble release is greatly enhanced by the use of a small heat gun or mini gas torch. Hold the torch approximately 100 to 150mm off the surface and keep moving the flame across the surface. Heat can be applied as many times as needed in the 30 minute working time. Inspect and remove any lint with tweezers. Clear Coating Epoxy Resin Epoxy should be cured in a warm 25°C, dust free area.

    Clear Coating Epoxy Resin is not to be thinned under any circumstances, as it has been formulated to optimal viscosity for this specific application.

    Title Type Size
    Fast Hardener - SDS application/pdf 574 KB
    Clear Coating Epoxy - SDS application/pdf 576 KB
    Clear Coating Resin - TDS application/pdf 251 KB
    Notify-me when it is back in stock We will inform you when the product arrives in stock. Just leave your valid email address below.
    Email Quantity We won't share your address with anybody else.